SARTORIUS MP30/11

Category: Tags: , , ,

Description

SARTORIUS MP30/01 P/N 9408 800 30011

SARTORIUS MP 30/20 P/N 9408 800 30201

SARTORIUS MP30/00 PN: 9408 800 30001

SARTORIUS MP30/10 Option Card – Relay output, 2 changeover contacts 9408 800 30101

SARTORIUS MP30/11 Option Card – Relay output, 4 relays 9408 800 30111

SARTORIUS MP30/20 Option Card – Analogue output 9408 800 30201

SARTORIUS MP30/31 Option Card – RS 232 interface 9408 800 30311

SARTORIUS MP30/32 Option Card – RS 485 interface 9408 800 30321

Minebea Intec digital weight indicator MP 30 – đầu cân, bộ chỉ thị kỹ thuật số, cân sàn, cân bồn, cân silo, cân phễu điện tử

Thông số kỹ thuật cơ bản của đầu cân, bộ hiển thị – digital weight indicator MP 30:

Protection class:
Housing: IP20
Panel mounted: IP65
Power supply:
85–250 VAC, 50/60 Hz
11–36 VDC or 24 VAC (Option)
Max. power consumption: 15 VA
Display:
Bright 5-digit LED display, 14 mm
Status symbols: brutto/gross, net, tare
Setpoint indication
Keypad:
5 keys for operation, calibration and configuration
Load cell excitation:
Jumper selectable: 5 VDC at 65 mA max. +/-2%
10 VDC at 125 mA max. +/-2%
max. four load cells of 350 Ω
Temperatur coefficient: 20 ppm/K max.
Digital control inputs:
3 configurable user inputs (TTL)
Input voltage: max. 30 VDC
Sink or source (aktiv/passiv) selectable
Sink: high Vin < 0.7 VDC, low Vin > 2.5 VDC
Source: high Vin > 2.5 VDC, low Vin < 0.7 VDC
Update rates:
Step response:
200 msec. max. to within 99 % of final readout value (digital filter and internal zero correction disabled)
700 msec. max. (digital filter disabled, internal zero correction enabled)
Environmental conditions:
Operating temperature range: 0 to 50°C (0 to 45°C with all three plug-in cards installed)
Storage temperature range: -40 to 60°C
Humidity: 0 to 85% max. non-condensing
A/D converter:
Resolution: 16 bit
A/D Conversion rate: 20 readings/sec.
Manual tare:
Configurable via front keys
Analog output MP 30/20:
2 analogue outputs with: 0/4–20 mA or 0–10 VDC
Isolation to sensor & user input commons Accuracy: 0.17 % of FS (18 to 28°C)
Resolution: 1/3500
Compliance: 10 VDC = 10 KΩ load min. 20 mA = 500 Ω load max.
Update time: max. 200 msec. filter and zero correction disabled Gross/net selectable
Setpoint output MP 30/10:
Type: 2 FORM-C relays Isolation to sensor & user input commons
Isolation to sensor & user input commons Total current: 5 A at 120/240 VAC or 28 VDC
Life expectancy: 100 K cycles min. at full load rating. Gross/net selectable
Setpoint output MP 30/11:
Type: 4 FORM-A relays
Total current: 3 A at 120/240 VAC or 28 VDC
Serial communications RS232 (MP 30/31) or RS485 (MP 30/32):
Isolation to sensor & user input commons
Settings: Databits: 7/8,
Baudrate: 300–19,200,
Parity: no/odd/even
Bus address: selectable 0–99, max. 32 devices per line (RS485)
Distance:
RS232: up to 15 m
RS485: up to 1200 m
Low frequency noise rejection:
Normal mode: > 60 dB at 50 or 60 Hz +/-1%, digital filter off,
Common mode: > 100 dB, DC to 120 Hz (w.r.t. earth)
Custom linearization:
Data point pairs: selectable from 2 to 16
Display range: -19.999 to 99.999
Decimal point: 0 to 0.0000
Hãng sản xuất: Minebea Intec ( NMB Minebea – MinebeaMitsumi Nhật Bản ).

Ứng dụng:

  • Cân bàn điện tử, cân sàn điện tử công nghiệp.
  • Cân bồn ngang, cân bồn chứa, cân phễu, cân silo.
  • Tank, Hopper Scale.

Tùy chọn của MP 30

  • MP 30/00: Digital Indicator 85 to 250 VAC
  • MP 30/01: Digital Indicator 11 to 36 VAC/DC
  • MP 30/10: Dual Relay Output for MP 30/0x
  • MP 30/11: Quad Relay Output for MP 30/0x
  • MP 30/20: Analog Output for MP 30/0x
  • MP 30/31: RS 232 Interface for MP 30/0x
  • MP 30/32: RS 485 Interface for MP 30/0x

Đặc tính kỹ thuật:

  • Nguồn cung cấp: 85 – 250 VAC 50/60 Hz hoặc 11 – 36 VDC/24 VAC (tùy chọn).
  • Đầu ra analog (tùy chọn): 0/4 – 20 mA hoặc 0 – 10 VDC.
  • Giao diện nối tiếp (tùy chọn): RS 232 hoặc RS 485.
  • Mặt trước kín, tiêu chuẩn chống nước, chống bụi: IP65.
  • Trừ bì thủ công: nhấn nhả phím TARE.

MP 30 Digital Weighing Indicator

MP 30 is suitable for less complex aplications where readability of measuerement is priority. Through its modular design it can easily be expanded with additional I/O or RS232/485 modules.

  • 16 bit resolution and up to 20 readings/sec.
  • Supply voltage: 85 – 250 VAC 50/60 Hz or 11-36 VDC/24 VAC (option)
  • 3 digital control inputs
  • Analog output (option): 0/4-20 mA or 0-10 VDC
  • Serial interfaces (option): RS 232 or RS 485
  • 2 setpoint outputs (option)
  • IP 65 sealed front panel
  • Manual tare

Typical versions of the indicator and options:

  • MP30/00 Digital indicator, 85-250 V AC 9408 800 30001
  • MP30/01 Digital indicator, 11-36 V AC/DC 9408 800 30011

Expansion cards:

  • MP30/10 Option Card – Relay output, 2 changeover contacts 9408 800 30101
  • MP30/11 Option Card – Relay output, 4 relays 9408 800 30111
  • MP30/20 Option Card – Analogue output 9408 800 30201
  • MP30/31 Option Card – RS 232 interface 9408 800 30311
  • MP30/32 Option Card – RS 485 interface 9408 800 30321

Đại lý SARTORIUS vietnam, SARTORIUS viet nam, SARTORIUS vietnam distributor, Phân phối SARTORIUS tại việt nam

Đại lý SARTORIUS vietnam, SARTORIUS viet nam, SARTORIUS vietnam distributor, Phân phối SARTORIUS tại việt nam

Đại lý SARTORIUS vietnam, SARTORIUS viet nam, SARTORIUS vietnam distributor, Phân phối SARTORIUS tại việt nam

Đại lý SARTORIUS vietnam, SARTORIUS viet nam, SARTORIUS vietnam distributor, Phân phối SARTORIUS tại việt nam

Đại lý SARTORIUS vietnam, SARTORIUS viet nam, SARTORIUS vietnam distributor, Phân phối SARTORIUS tại việt nam

 

Reviews

There are no reviews yet.

Be the first to review “SARTORIUS MP30/11”

Email của bạn sẽ không được hiển thị công khai. Các trường bắt buộc được đánh dấu *

Related products